Engineering   |   General   |   Hardware   |   Machinery   |   Routing   |   Woodworking
Home  >>   News   >>   About Us   >>   Freight   >>   Contact Us  >>   Shopping Cart
ROUTER / ACCESSORIES
TRIM ROUTER
2 IN 1 ROUTER & SAW DEPTH GAUGE
ADAPTOR BUSHING
BALL BEARING GUIDE
BEARING STOP
FOAM TRAY ROUTER BIT ORGANIZER
ROUTER BIT TRAY
ROUTER BUSHING GUIDE CENTERING PIN
ROUTER CENTRE PIN
ROUTER COLLET EXTENSION
ROUTER DEPTH GAUGE
ROUTER INSTALLATION KIT
ROUTER PANTOGRAPH
ROUTER SPEED CONTROL
SIGN-MARKING TEMPLATE SET

Category Browser
TRIM ROUTER

The 1-HP motor speed is adjustable from 10,000 rpm to 30,000 rpm via a speed control dial on the top of the motor housing. Etched into the aluminum housing is a 1" long rule marked in 1/16" and 1mm increments. The double insulated motor features a spindle-locking button to facilitate single wrench bit changes. The metal base uses a rack and pinion system to adjust the height of the motor and a flip lever to lock the motor at the desired height. In addition, a rubber pad partially wraps the base to provide a positive gripping surface when holding the router in your palm.

ITEM NO. DESCRIPTION WEIGHT(g) PRICE QUANTITY IN STOCK ORDER NOW
TR9056 240V, 50Hz, 710W, 10000~30000/min (1/4") 1500 $95.00 Yes
2 IN 1 ROUTER & SAW DEPTH GAUGE
You can adjust router or table saw height & depth of cut accurately in seconds. The aluminum gauge is marked from 1/8" to 1" in 1/16 of an inch increments.
ITEM NO. DESCRIPTION WEIGHT(g) PRICE QUANTITY IN STOCK ORDER NOW
MJ-840 1/8" ~ 1" 50 $12.00 No
ADAPTOR BUSHING
Steel adaptor bushings used to reduce the collets size for smaller diameter shank bits, end mills, drill bits , and dremel bits. Never exceed the recommended RPM of the cutting tool.
ITEM NO. DESCRIPTION WEIGHT(g) PRICE QUANTITY IN STOCK ORDER NOW
JL-271 Outer 1/4", Inner 1/8" 10 $6.00 Yes
JL-272 Outer 1/4", Inner 3/16" 10 $6.00 Yes
JL-275 Outer 1/2", Inner 1/4" 30 $6.00 Yes
JL-276 Outer 1/2", Inner 5/16" 30 $6.00 Yes
JL-277 Outer 1/2", Inner 3/8" 20 $6.00 No
JL-278 Outer 8mm, Inner 6mm 20 $6.00 Yes
BALL BEARING GUIDE
These pilot bearings are totally enclosed. By changing the bearing outer diameter and profiles will result.
ITEM NO. DESCRIPTION WEIGHT(g) PRICE QUANTITY IN STOCK ORDER NOW
JL255 Inner 3/16", Outer 3/8" 10 $4.00 Yes
JL256 Inner 3/16", Outer 1/2" 10 $4.00 Yes
JL257 Inner 3/16", Outer 5/8" 20 $4.00 Yes
JL258 Inner 3/16", Outer 3/4" 30 $4.00 Yes
JL259 Inner 3/16", Outer 7/8" 30 $4.00 Yes
JL270 Inner 5mm, Outer 9mm 10 $4.00 Yes
JL247 Inner 5mm, Outer13mm 10 $4.00 Yes
JL248 Inner 5mm, Outer 16mm 20 $4.00 Yes
JL249 Inner 5mm, Outer 19mm 30 $4.00 Yes
JL260 Inner 1/4". Outer 1/2" 20 $5.00 Yes
JL261 Inner 1/4". Outer 5/8" 30 $5.00 Yes
JL262 Inner 1/4", Outer 3/4" 30 $5.00 Yes
JL266 Inner 8mm, Outer 22mm 20 $5.00 Yes
JL231 Inner 8mm, Outer 28mm 30 $6.00 No
JL263 Inner 1/2", Outer 3/4" 20 $5.00 Yes
JL265 Inner 1/2", Outer 1" 30 $5.00 Yes
JL227 Inner 1/2", Outer 1-1/4" 40 $6.00 Yes
BEARING STOP
To stop the bearing moving,when build up top mouted cutterrs.
ITEM NO. DESCRIPTION WEIGHT(g) PRICE QUANTITY IN STOCK ORDER NOW
JL-BS14 For 1/4" Shank, 1.5mm Hex Key 10 $4.00 Yes
JL-BS12 For 1/2" Shank, 2mm Hex Key 20 $5.00 Yes
FOAM TRAY ROUTER BIT ORGANIZER
Use this 100 hole organizer in custom tool boxes, cut exactly what you need. Dense foam keeps even the biggest bits in position to protect them from damage.
ITEM NO. DESCRIPTION WEIGHT(g) PRICE QUANTITY IN STOCK ORDER NOW
ROUTER-OT 1/4" x 60, 1/2" x 50, (110 Holes). 200 $28.00 Yes
ROUTER BIT TRAY
Keep your rotary tools well organized and safe, protecting your investment for years to come. Each tray contains 40 holes and is moulded from sturdy ABS plastic. Comes in 5 different hole diameters to accommodate the majority of tool shanks available today. Trays can be glued into drawers or left on your work bench for easy access.

W1038-12 tray with 1/2" , 8 holes

W1038-14 tray with 1/4" , 40holes

ITEM NO. DESCRIPTION WEIGHT(g) PRICE QUANTITY IN STOCK ORDER NOW
W1038-14 1/4" x 40 Holes 100 $4.00 Yes
W1038-12 1/2" x 8 Holes 100 $4.00 Yes
ROUTER BUSHING GUIDE CENTERING PIN
This uniquely designed bushing guide centering pin works with 1/4" or 1/2" shank router collets. Chuck the straight end into router colets,and raise the bushing guide until it centers on the tapered edges of the centering pin to align the base plate to the collet. This will give you perfect router bit alignment. The center pin is positioning device only and is not to be used on any running machinery.
ITEM NO. DESCRIPTION WEIGHT(g) PRICE QUANTITY IN STOCK ORDER NOW
TCN1 1/4" or 1/2" shank edges centering pin 80 $12.00 Yes
ROUTER CENTRE PIN
Are your dadoes and ornamental cuts sometimes a bit off? Slip this new pin-point precision gauge into your router (fits both 1/4" and 1/2"), and it will put every cut on target! With your router inverted, hold a square in place and rotate the gauge to check for run out or wobble. 3"long x1/2" diameter.
ITEM NO. DESCRIPTION WEIGHT(g) PRICE QUANTITY IN STOCK ORDER NOW
D423-00 1/4" and 1/2" 200 $8.00 Yes
ROUTER COLLET EXTENSION
Give your router bits an additional 2-1/4"(65mm) when you extend them through the router table top with our router Collet extension. Eliminate the dangerous temptation of withdrawing the shank from the Collet in order to raise the bit and to provide the full depth of cut.The router Collet extension makes it possible to use all diameters of 1/2" and 1/4" shank bits safely. Place the router Collet extension shank in the 1/2" router Collet and the router bit shank in the extension Collet and tighten both.
ITEM NO. DESCRIPTION WEIGHT(g) PRICE QUANTITY IN STOCK ORDER NOW
EX9468 Collet 1/4", Shank 1/2", 25 x 100mm 200 $55.00 Yes
EX9464 Collet 1/2", Shank 1/2", 25 x 90mm 300 $55.00 Yes
ROUTER DEPTH GAUGE
No more guessing! You can adjust router height & depth of cut accurately in seconds using Router Depth Gauge. The aluminum gauge is marked from 1/8" to 1" in 1/16 of an inch increments.
ITEM NO. DESCRIPTION WEIGHT(g) PRICE QUANTITY IN STOCK ORDER NOW
MJ-830 1/8" ~ 1" 30 $6.00 Yes
ROUTER INSTALLATION KIT
This kit is used to install the RTS-1 router plate into a shop made router table.
A special spacer collar produces the stepped recess for the base plate using the same router bit. Allowance has been made for expansion due to heat and humidity and variations caused by using previously sharpened router bits
ITEM NO. DESCRIPTION WEIGHT(g) PRICE QUANTITY IN STOCK ORDER NOW
RK-01 3T 500 $95.00 Yes
ROUTER PANTOGRAPH

For use with routers that have a 6"(152mm) round base plate.For making wooden signs, plaques and nameplates. Router attaches to universal mounting plate for tracing letters and drawings.
Stencils included: Modern and old English capitals, small letters, and numbers.The pantograph can be adjusted to give three different ratios of reduction from template to engraving, for 42%, 50%, and 58%.

ITEM NO. DESCRIPTION WEIGHT(g) PRICE QUANTITY IN STOCK ORDER NOW
F-3020 With stencil, 42%,52%,58% 1000 $60.00 Yes
ROUTER SPEED CONTROL

Simply power plug in speed control then plug your router into the speed control. Switch to Vario (10000 to 30000rpm) or Full (fast speed). The Speed Control features a plastic case, and is recommended for commercial use. Speed Control is suitable for home shop trim router or other power tool <1HP (750W)

ITEM NO. DESCRIPTION WEIGHT(g) PRICE QUANTITY IN STOCK ORDER NOW
SCR-10A FOR 1HP ROUTER (750W.240V, 10A) 500 $60.00 Yes
SIGN-MARKING TEMPLATE SET
For making wooden signs, plaques, and nameplates.Templates included to make 1-1/2" (38mm) and 2-1/2" (63.5mm) letters and numbers. Use 1/4" and 1/2" straight V-groove or Cove router bits for different letter styles. Self spacing system eliminates need to measure between letters. Clamps for holding templates frame to your workpiece. Template holder takes up to 8 letters for fast sign making.
ITEM NO. DESCRIPTION WEIGHT(g) PRICE QUANTITY IN STOCK ORDER NOW
F-3015 1-1/2"~2-1/2" High, 4"~12" Wide 1300 $60.00 Yes
454 HUME HWY. YAGOONA 2199 NSW TEL:(02)9709 8805 FAX:(02)9709 8831