Engineering   |   General   |   Hardware   |   Machinery   |   Routing   |   Woodworking
Home  >>   News   >>   About Us   >>   Freight   >>   Contact Us  >>   Shopping Cart
Browse Our Products
Engineering
General
Hardware
Machinery
Routing
Woodworking

Special Products
PRESS CLAMP
Design and build your own press clamping system with this 5/8"x 8" and 1"x12" square thread press screw.
Ideal for making veneering frames and deep-reach surface clamping.

CHANGEABLE CARBIDE WOODTURNING SET
One 12" handle and 6" round bar flat both side with grab locking screw. Also have a clear safety glass. Set included four piece carbide tipped tips, (10mm curve, round, flat and point )  .
WOOD KNURLING SET
6pc knurling wheels: 3pc Straight Pitch 1mm,1.5mm,2mm, 3pc Cross Pitch 1mm,1.5mm,2mm.

10x10x220mm Square Bar Holder easy to change different wheels.
MINI DRIVE CENTRE / LIVE CENTRE
Mini Drive Centre  spring loading pin, 3/8" (9.5mm) safety ring, MT.2
Mini Live Centre
  with 90° / 60°nose and 22mm diameter, twin bearings .Tool access is important when turning small items and it has far less tendency to act as a wedge when small.
Those MT.2 versatile drive / live centre using small section brittle,split material or off-centre end grain woodturning .
TORQUE WRENCH
The accuracy of Torque Wrenches exceeds all International standards, with a traceable calibration certificate supplied with each wrench to satisfy ISO9000 quality systems.Accurate to within +/-3% of reading & are graduated in Nm & ft/lb for foolproof & accurate setting.The micrometer type sleeve allows accurate preset torue levels to be set. High quality, reversible ratchets allow work in confined areas.Handle material & lens resist all chemicals in common automotive, industrial & avaiation use.Packaged in a blow mould case.

CHIPBOARD CONNECTOR SCREW
High quality once piecer connector. Deep cutting threads ensures accurate and close fitting joints. 5 or 7mm thread diameter to suit 3.2 or  4.7mm hole diameter. 3 or 4mm positive Hex driver or POZI. driver countersunk head. Made from Steel, Zinc plated for protection.
TOY WHEEL CUTTER
This uniquely designed tool can create beautiful toy wheel using only your drill press or lathe. The heavy, solid steel molding head mounts into the drill press chuck and accepts a variety of high speed steel cutter shapes. Clamp your choice of wood in place and feed the cutter into  the wood as in normal drilling operations. Requires a 1/2" shank capacity drill chuck. For best results, cut at 300~500 rpm.
Wheel Diameter x Wheel Thick x Shank
SAFETY NOTE: NOT INTENDED FOR HAND DRILL OR ROUTER USE
UNIVERSAL BASE PLATE
After time, router base plates become scratched, worn or damaged from use. Some routers come from the factory without accepting the industry standard Porter Cable size router bushing. This universal plate Solves these problems and adds visibility by being clear acrylic. Fits routers: Porter Cable 690,7529, 8529 Ryobi Most Models, Bosch 1615, 1617, 1618 ,Makita Most Models 315 275 000, 315 175 040, 315 175 050,315 175 060, 315 175 070, 315 275 100, 315 275 110, Fein FT 1800, Hitachi M8V, TR12, M12V, Elu 177, Dewalt  621, 625, 616, 618
BRASS BUSHING KIT
The 9 piece kit will significantly expand the use of your router. For template controlled operations such as dovetailing, stair routing, hinge butt routing, omni jig template, lock face routing and other general template operations. Template guides can be used directly with universal base plate with a 30mm hole (35mm recess) . The kit contains two lock nuts and seven different template guides ID/OD ( 6/7.9mm, 7/9.5mm, 8.6/11.1mm, 10/12.7mm, 13.3/15.9mm, 15.8/20.2mm, and 16.4/19mm).
PEN MANDREL & SAVER
Mandrels usually bend when you tighten the tailstock center point into the end indentation of your mandrel.This system solves that problem because your mandrel shaft goes through the hollow live center. The mandrel system including MT Drive Center with a basic mandrel and 3 bushings (no threads or knurled nut) PLUS Mandrel Saver Tailstock. Your  bushings press against the center with  zero pressure on the mandrel shaft.
If you have a drive mandrel shaft already you can order a Mandrel Saver only .
BENCHTOP ROUTER TABLE
23-3/4" x 15-3/4"  Router Table Top,  23-3/4" Router Table Fence.  Miter Track  / T-Track / Hardware
More than 250Lbs load capacity.
( Router machine not included )
HORIZONTAL ROUTER TABLE
This is one of the most unique router tables yet it's also one of the handiest and versatile in the shop. A horizontally mounted router that can be finely adjusted allows the woodworker to use vertical raised panel bits with ease and safety. The large table surface supports the largest doors. With a few shop made jigs, it's also the perfect mortising machine.( Router machine not included )
Feature Products
WOOD MOISTURE METER
Material range : Wood,  Bamboo, Tobacco, Cotton, Paper, etc.
EM2G(2point)  Measure Range: 6~25%,  Accuracy: 2%,  Display:LED,  Resolution: 1%, Power: 9v 6f22 battery.
EM4G(4point)  Measure Range: Low 7~15%,High 16~35%,  Accuracy: 1%,  Display:LED,  Resolution: 1%, Power: 9v 6f22 battery.
2 in 1 DOWELING JIG KIT
Easily match Face-to-Edge or Edge-to-Edge holes for dowel joining. Will drill the following hole sizes: (inch.) 1/4", 5/16", and 3/8" . Holds stock up to 1-1/4".
It needs no markings. Drill holes for edge to edge and edge to surface edge dowel joints.
VENEER ROLLER
The differences are in the handle design.These rollers efficiently apply operator pressure to laminates and veneers for positive glue contact. Both have comfortable grips and rubber roller for even pressure distribution. The handle come in two different styles with 3" wide roller.
STICK ON TAPE RULE
New Metric (1200mm)
1/2" (13mm) wide tape, Peel off the back to expose the adhesive, and apply where meet your shop needs.
BROACH CUTTER / ADAPTER
HSS-E or Tungsten Carbide Tipped, Suit 19mm shank Slug Socket Magnetic Base Drill (MBD19 , MBD25) ,
Some size x 50mm depth available.

MT.2 or MT.3 adapter to suit broach cutter with 19mm shank ,Ideal for magnetic drill with MT.2 or MT.3, And bench and pedestal drill .
 
EARTH AUGER / POST HOLE DIGGER
Engine model : 1E44F-2A, Forced air-cooled, 2 stroke, single cylinder.  Fuel tank capacity : 1.2 .  Gasoline / Oil mix ration :  30:1 , Displacement  51.7ml/cc. 
Engine Speed  8500rpm.   Rated Power 1.4kw,  Max Torque  2.3N.m  ,  Carburetor Diaphragm Type. 

Ignition : C.D.I  , Starting : Recoil starter
ELECTRIC MOTOR
Single phase 240V/50HZ, 19mm Shaft, Start / Stop.

Base hole between center : 100 x 125mm
220x40 LOW SPEED WET SHARPENER
240V / 50HZ,  180W,   Wet stone wheel size: 220x40mm, Leather wheel size: 220x30mm, Strop / Honing speed :125rpm.  Motor no load speed : 2850rpm , Noise level  <70db.
Include : Supper arm assembly, Straight edge jig, Angle protractor, Honing compound, Stone grader.
SWIVEL SPINDLE CASTOR with BRAKE
If you have limited shop space, or just have a lot of materials to move around, then just imagine the tremendous flexibility and convenience you'll get by putting cabinets, carts, tools, and work stations on wheels. 3" Caster, Double Locking, Swiveling with 3/8" Threaded Spindle.

SIGN-MARKING TEMPLATE SET
For making wooden signs, plaques, and nameplates.Templates included to make 1-1/2" (38mm) and 2-1/2" (63.5mm) letters and numbers. Use 1/4" and 1/2" straight V-groove or Cove router bits for different letter styles. Self spacing system eliminates need to measure between letters. Clamps for holding templates frame to your workpiece. Template holder takes up to 8 letters for fast sign making.
454 HUME HWY. YAGOONA 2199 NSW TEL:(02)9709 8805 FAX:(02)9709 8831