Engineering   |   General   |   Hardware   |   Machinery   |   Routing   |   Woodworking
Home  >>   News   >>   About Us   >>   Freight   >>   Contact Us  >>   Shopping Cart
Browse Our Products
Engineering
General
Hardware
Machinery
Routing
Woodworking

Shop Open:  Monday ~ Friday 9:00 am ~ 4:30 pm .    Saturday 9:00 am ~ 12:30 pm .  
Special Products
BENCH HOLD FAST
BHF19250C, Made by Cast iron, A  very traditional way of holding workpieces. Place in 3/4" hole, and whack with a mallet. Hit the back of the clamp to release.

BHF19250B, Bent metal bar with knurl allows easy re-positioning and stop moving. ( If you don't like the knurl bar, Just file it and make smooth touch face ), Simple but effective heavy duty iron hold-fasts quickly clamp and release small boards or large blocks of wood. Place the clamp in 3/4" hole, and whack with a mallet. Hit the back of the clamp to release.  ( 9 )

For 3/4" (19mm) Hole Bench Top     Diameter x Bar Length x Reach 
ADJUSTABLE DRILL STOP SET
Two piece stop collar set fits all drill bits from 1.5mm to 12.7mm. The smaller one takes bits from 1.5 - 6.4mm, and the larger takes 6.4 - 12.7mm bits. Designed with double-ended collets inside threaded sleeves, they lock in position with a quick twist. They are handy, versatile stops for the shop or toolbox.  ( 11-3 )
BLOCK PLANE
"LUBAN" (QIANGSHENG) Block plane sits firmly in the palm and with bronze lever cap. This finely crafted block plane is designed for general purpose soothing and shaping, paring end grain, cleaning up components by removing thin shavings in order to make a component fit within tight tolerances, chamfering and cleaning up glue lines.
CBN GRIDING WHEEL
CBN is Cubic Boron Nitride. Don't have to worry about dressing or shaping like typical aluminum oxide wheels. It's perfect for sharpening HSS turning tools. You will achieve a super fine, sharp edge with polished bevel on either hardened tool steel or carbide. CBN Grinding Wheel are very quiet, produce very little sparks and generate very little heat when sharpening. The steel wheel body with hollow recessing bushing to make it light.

Diameter x Width x Bore,   Grit
DIAMOND GOUGE HONE
Every woodturner will like it, This new design Diamond Gouge Hone one side 6mm Rod (R3) and one side 12mm Rod (R6) with 600grit diamond hone. The body with magnets holding metal rod perfectly and it can be turn round use circle face of plated diamond. also two flat side of body with G400 / G600 ,  R3 and R6 radius covers most of woodturning gouges.
DIAMOND KNIFE HONE
Four sides flat knife hone with handle ( 3-side 300G/600G/1000Grit diamond hone, 1-side leather hone ), Easy operated for sharpening pocket knife or kitchen knife etc. ( 5 )
CARBIDE ROUND TIP
This 12mm round carbide tip with 4mm countersink hole is very useful. Tapping M4 thread to the holder you can build up your-self to make detail or boring and hollowing tools.
RECHARGEABLE LED WORKLIGHT
This new arrival LED worklight with strong 40mm magnetic base ideal for workshop such as Lathe, Milldrill, Drill press, Bench Grinder,etc with metal stand. Sunny light wireless make work easy and it can be recharge for more power. 
DIAGONAL CUTTER (PLIERS)
New arrival 4" mini diagonal cutter.
STAINLESS TWEEZERS
Click picture for big Image
T-TRACK
Check: HARDWARE for T-TRACK / MITRE TRACK / FIXTURE
This aluminum extrusions 3/4" (19mm ) x 1/2"(12mm) T-Track fits M8 or 5/16" T- bolts or  standard hexagonal head bolts (13mm ). 
The lengths are available in 1252mm and 2505mm, Not be Allowed by post ( pick up only ). Please contact us for current stock lengths.


UNIVERSAL FENCE CLAMP
With this adjustable clamp, you'll always have the correct size fence clamp available. Perfect for holding sacrificial fence boards for rabbeting. Simply drill a 3/8" hole in the top of the auxiliary fence and secure it with the clamps to your existing system. 
FLIP STOP for T-TRACK
Fully adjustable solid aluminum stop on T-track allows repeatable accuracy. Aluminum stop for 1/4" mini T-track slot, Flips out of the way if you need to make an odd cut in the middle of the run. Easy to use - just slide onto your t-track, Set to desired measurement and make repetitive cuts without re-measuring each time.

FOLDING SHELF BRACKET with CLIP HANDLE
These folding shelf brackets with clip handle lock themselves securely in position when changed section. Loading capacity 100kg. Material thick 1.5 x 1.5 x 2.5mm.
The brackets come in white and are sold in pairs.
Simple space saving convenience for when you need a shelf just some of the time.
TRIM ROUTER

The 1-HP motor speed is adjustable from 10,000 rpm to 30,000 rpm via a speed control dial on the top of the motor housing. Etched into the aluminum housing is a 1" long rule marked in 1/16" and 1mm increments. The double insulated motor features a spindle-locking button to facilitate single wrench bit changes. The metal base uses a rack and pinion system to adjust the height of the motor and a flip lever to lock the motor at the desired height. In addition, a rubber pad partially wraps the base to provide a positive gripping surface when holding the router in your palm.

ROUTER BUSHING GUIDE CENTERING PIN
This uniquely designed bushing guide centering pin works with 1/4" or 1/2" shank router collets. Chuck the straight end into router colets,and raise the bushing guide until it centers on the tapered edges of the centering pin to align the base plate to the collet. This will give you perfect router bit alignment. The center pin is positioning device only and is not to be used on any running machinery.
ROUTER CENTRE PIN
Are your dadoes and ornamental cuts sometimes a bit off? Slip this new pin-point precision gauge into your router (fits both 1/4" and 1/2"), and it will put every cut on target! With your router inverted, hold a square in place and rotate the gauge to check for run out or wobble. 3"long x1/2" diameter.
BOWL & TRY TEMPLATE SET
Here's the easiest way to make beautiful bowls and trays with the router. Start with an inside template of the design you want fastened to the selected piece of wood. Rough out the large center area, Mount the correct router bit and route. Rotate the template around and router until all desired areas of the board are cleared out. Bandsaw the outside and sand smooth. Kit includes: 1pc 23½" oval template,1pc 17½" circle template,1pc 17½" 3 side template,1pc 17½" 4 side template, 1pc 12" 4 side mini template
BRASS GUAGE
4pc  2-1/2" long brass bars, measuring 3/16", 1/4", 3/8", and 1/2" square are included.

1pc 1/4" pin taper to 5/8" , This taper pin ideal for guided finding centre with universal base plate.
BUSHING LOCK WASHER
The 1-3/16” O.D. spring steel lock washer provides resistance to your template guide bushings. The unique “bent” design of the ring keeps pressure on the locking nut to prevent router vibration from loosening the nut.
2-JAW PEN BLANK CHUCK
Drill a perfectly centered hole in your blank on your lathe using this unique lathe chuck.  The chuck includes two jaws that will hold your blanks perfectly centered at the headstock.  Mount a drill chuck with your drill bit into your tailstock and advance the drill into your blank as it spins on your lathe.

PEN MANDREL & SAVER
Mandrels usually bend when you tighten the tailstock center point into the end indentation of your mandrel.This system solves that problem because your mandrel shaft goes through the hollow live center. The mandrel system including MT Drive Center with a basic mandrel and 3 bushings (no threads or knurled nut) PLUS Mandrel Saver Tailstock. Your  bushings press against the center with  zero pressure on the mandrel shaft.
If you have a drive mandrel shaft already you can order a Mandrel Saver only .
PEN MILL
For dressing the end of pen blank. Slide the post into the pen barrel and rotate to mill the ends square.   
Note:  Standard brass tube outside dia. 7mm inside dia. 6.3mm. So PM1006.2 are more popular.
MULTI-JOINT SPACING SYSTEM
The Multi-joint spacing system allows you to make 1/4", 3/8" and 1/2" box joints as well as rabbet, dado, spline and sliding dovetail joints (for drawer glides) to any width with no limitation. Brass set-up bars (included) make setting up the Multi-joint very simple. Made from durable laminated MDF with UHMW guide bars for smooth operation. Platform measures 24" long which will fit across most router tables. Use your own bits or purchase one of ours. Please Note: This system is designed to be used on table mounted routers only.Set Including: 1pc 1/4" Spacer Fence.1pc 3/8" Spacer Fence,1pc 1/2" Spacer Fence,1pc Positive Stop Setup Block,1pc Dovetail Liner Offset Fence,3pc Right Angle Fences,4pc Brass Set-Up Bars.
BENCHTOP ROUTER TABLE
23-3/4" x 15-3/4"  Router Table Top,  23-3/4" Router Table Fence.  Miter Track  / T-Track / Hardware
More than 250Lbs load capacity.
( Router machine not included )
MORTISE CENTERING ROUTER BASE
Perform easy mortises with the router without the fear of keeping the guides firmly against the work. The adjustable guide block slides around a semi-circular slot making contact with the project. Here it locks in position to keep the router in full control. The clear acrylic base allows full view of the work. An insert specifically used for marking and positioning the base is supplied. Guide pins are adjustable for material thicknesses up to 4-3/4".

MOTOR V-BELT
Rubber V fraction motor pulley drive belt are poly amide wedged.
Wide x Height :   
K section 8 x 4mm.  M/Z/O
section 10 x 6mm.       
A
section 13 x 8mm.   B section 17 x 11mm.
Other Section and Size may available.
Feature Products
VENEER ROLLER
The differences are in the handle design.These rollers efficiently apply operator pressure to laminates and veneers for positive glue contact. Both have comfortable grips and rubber roller for even pressure distribution. The handle come in two different styles with 3" wide roller.
BROACH CUTTER / ADAPTER
HSS-E or Tungsten Carbide Tipped, Suit 19mm shank Slug Socket Magnetic Base Drill (MBD19 , MBD25) ,
Some size x 50mm depth available.

MT.2 or MT.3 adapter to suit broach cutter with 19mm shank ,Ideal for magnetic drill with MT.2 or MT.3, And bench and pedestal drill .
 
EARTH AUGER / POST HOLE DIGGER
Engine model : 1E44F-2A, Forced air-cooled, 2 stroke, single cylinder.  Fuel tank capacity : 1.2 .  Gasoline / Oil mix ration :  30:1 , Displacement  51.7ml/cc. 
Engine Speed  8500rpm.   Rated Power 1.4kw,  Max Torque  2.3N.m  ,  Carburetor Diaphragm Type. 

Ignition : C.D.I  , Starting : Recoil starter
ELECTRIC MOTOR
Single phase 240V/50HZ, 19mm Shaft, Start / Stop.

Base hole between center : 100 x 125mm
220x40 LOW SPEED WET SHARPENER
240V / 50HZ,  180W,   Wet stone wheel size: 220x40mm, Leather wheel size: 220x30mm, Strop / Honing speed :125rpm.  Motor no load speed : 2850rpm , Noise level  <70db.
Include : Supper arm assembly, Straight edge jig, Angle protractor, Honing compound, Stone grader.
SWIVEL SPINDLE CASTOR with BRAKE
If you have limited shop space, or just have a lot of materials to move around, then just imagine the tremendous flexibility and convenience you'll get by putting cabinets, carts, tools, and work stations on wheels. 3" Caster, Double Locking, Swiveling with 3/8" Threaded Spindle.

SIGN-MARKING TEMPLATE SET
For making wooden signs, plaques, and nameplates.Templates included to make 1-1/2" (38mm) and 2-1/2" (63.5mm) letters and numbers. Use 1/4" and 1/2" straight V-groove or Cove router bits for different letter styles. Self spacing system eliminates need to measure between letters. Clamps for holding templates frame to your workpiece. Template holder takes up to 8 letters for fast sign making.
454 HUME HWY. YAGOONA 2199 NSW TEL:(02)9709 8805 FAX:(02)9709 8831